Guide to Factory Reset Your Holosun EPS Carry Red Dot Aimpoint

Wiki Article

Need to return your Holosun EPS Carry Red Dot Scope to its factory settings? It's easier than you think. This guide will walk you through the simple steps to perform a factory reset on your red dot, restoring it to its original configuration.

First, locate the small lever on the rear of your sight. This is the reset button.

• Activate and toggle the reset lever to initiate the factory reset procedure.
• Pause for a few seconds while your Holosun restarts itself. You'll notice a series of flashes or changes to the display as it completes the process.
• The Holosun EPS Carry Red Dot aimpoint is now reset to factory settings. You can now proceed with adjusting your preferences as desired.

Return Your Holosun EPS Carry to Factory Defaults

Sometimes, you might find yourself needing to reset your Holosun EPS Carry back to its factory settings. This can be beneficial in a number of scenarios. Perhaps you've been experimenting with different configurations and want to start fresh, or maybe your sight is acting strange. Whatever the reason, resetting your EPS Carry to its factory defaults is a relatively simple process.

• First, you'll need to locate the reset button on your Holosun EPS Carry.
• Using a small tool, carefully press and hold the reset button for approximately five seconds. You'll observe a change in the display, indicating that the device is being a reset.
• After the reset is complete, your Holosun EPS Carry will be back to its factory defaults. You can then reconfigure the sight as needed.

Restore Your Holosun EPS Carry Back to Basics: A Factory Reset

Sometimes your red dot might need a little boost. If you're experiencing performance problems with your Holosun EPS Carry, a factory reset could be the solution you need. This simple process will erase all user settings and return your sight to its default configuration.

• A factory reset is perfect for resolving electronic problems that can't be fixed by other means.
• Make sure to back up any important settings you want to keep before performing a factory reset.
• During process, your sight will refresh. This is expected and indicates that the reset is happening correctly.

After the factory reset, you'll need to adjust your sight to your needs. This includes adjusting the brightness, reticle type, and other features.

Refer to your Holosun EPS Carry's user manual for detailed instructions on how to perform a factory reset and reconfigure your sight.

Factory Reset Your Holosun EPS Carry In Detail

The Holosun EPS Carry is a robust red dot sight known for its effectiveness. Like any electronic device, it may sometimes require a recalibration to resolve certain issues or diagnose. This guide will walk you through the step-by-step process of performing a factory reset on your Holosun EPS Carry.

Before you begin, ensure that you have a fresh battery installed in the sight. Pay attention to these steps carefully:

• Simultaneously press and hold both the function button and the on/off switch for approximately ten seconds.
• Let go of both buttons when you see the red dot flash.
• Pause until the red dot returns to its normal output.

Your Holosun EPS Carry is now factory reset. It will return to its default settings and behavior.

Accessing Your Holosun EPS Carry: The Factory Reset Method

Factory resetting your Holosun can fix several common problems.

This procedure restores your optic to its default settings, which can be helpful if you're experiencing unexpected behavior.

Before you start, ensure your sight is turned off.

To conduct the factory reset, you'll utilize a small object to press the button located more info on the rear of your device.

Check out are the steps:

• Power off your Holosun EPS Carry.
• Find the reset button on your sight. It's typically a small, recessed button.
• Use a small object to press and hold the reset button for approximately five milliseconds. You'll likely see a brief flash indicating the reset is in progress.
• Let go of the reset button and wait your sight to reboot. Once it's operational, you'll be back to the factory settings.

By adhering to these steps, you can successfully reset your Holosun EPS Carry.

Quickly Reset Your Holosun EPS Carry Parameters

Need to refresh your Holosun EPS Carry back to its original settings? No problem! A factory reset is fast and easy. Begin with accessing the menu on your sight. Look for the "reset" function. Hold down the appropriate buttons until you see a confirmation indicator. Now your EPS Carry is back to brand new, ready for zeroing and customization.

Report this wiki page